Drone
LARK DIY Drone kit
SPECIFACTION
| Brand | CX MODEL |
| Item model | CX-002 |
| Item name | quadcopter |
| Remote controller | 2.4G Remote Control |
| Gyroscope | Six axis |
| Main material | ABS |
| Battery charger | USB plug |
| Functions | Sideward flight/One key takeoff/One key landing/Turn left/right, Up/down,Forward/backward/3D Flip/Altitude Hold |
| Control Distance | about 50m |
| Quadcopter Battery | 3.7V 400mAh lipo battery |
| Battery Size | 38 * 20 * 8mm |
| Charging time | about 40 minutes |
| Working time | about 7 minutes |
| Controller Battery | 2 * AAA Battery(not included) |
| Product weight | about 47g |
| Product size | 150 * 140 * 35mm |
DIY Building Block Quadcopter woth 480 camera
SPECIFACTION
| Camera | 0.3MP |
| Battery of drone | 3.7V 350mAh battery |
| Battery of transmitter | 3×AAA (not included) |
| Charging time | 55minutes |
| Flying time | 6-7 minutes |
| Remote control distance | <=40meter |
| Size | 11.8*11.8*4.9cm |
KK2.1.5 Flight Controller board
SPECIFACTION
| Model | KK2.1.5 |
| Input Voltage (V) | 4.8V-6.0V |
| Firmware | Pre-installed firmware |
| Sensors | 6050 MCU |
| Processor | Atmel 644PA |
| Micro-SD Card Slot | No |
| Length (mm) | 52 |
| Width (mm) | 52 |
| Height (mm) | 12 |
| Weight (gm) | 26 |
| Shipment Weight | 0.145 kg |
| Shipment Dimensions | 10 × 6 × 40 cm |
CC3D Flight Controller Board
SPECIFACTION
| Model | OpenPilot CC3D EVO Straight Pin |
| Input Voltage (V) | 5 VDC |
| Sensors | 3-Axis Gyrometer, Accelerometer,High-performance Barometer |
| Processor | Micro-Controller STM32, Sensor IC: MPU6000 |
| Micro-SD Card Slot | No |
| Dimensions (mm) LxWxH | 40 x 40 x 18 |
| Weight (gm) | 22 |
| Shipment Weight | 0.115 kg |
| Shipment Dimensions | 8 × 7 × 5 cm |
BLDC Motor
SPECIFACTION
| Model | A2212 10T 13T |
| Motor KV (RPM/V) | 1000 |
| Current Handling Capacity | 12A/60S |
| No-Load Current | 0.5A @10V |
| Max. Efficiency Current | 4-10A |
| LiPO Batteries | 2S-3S |
| Shaft Diameter (mm) | 3.17 |
| Maximum Efficiency | 80% |
| Length (mm) | 27.5 |
| Width (mm) | 27 |
| Weight (gm) | 64 |
| Shipment Weight | 0.145 kg |
| Shipment Dimensions | 12 × 6 × 5 cm |
DC Gear 200rpm Motor
SPECIFACTION
| Gear Material | Plastic |
| Rated RPM | 100 |
| Operating Voltage(VDC) | 12 |
| Rated Torque(kg-cm) | 2.9 |
| Stall Torque(Kg-Cm) | 11.4 |
| Load Current(A) | 0.3 |
| No-Load Current | 60mA |
| Gearbox Diameter (mm) | 37 |
| Motor Diameter(mm) | 32 |
| Motor Length(mm) | 75 |
| Shaft Diameter (mm) | 6 |
| Shaft Length (mm) | 22 |
| Weight (gm) | 80 |
| Shipment Weight | 0.195 kg |
| Shipment Dimensions | 10 × 5 × 5 cm |
BO Motor straight shaft 300RPM
SPECIFACTION
| Operating Voltage(VDC) | 3~12 |
| Shaft Length (mm) | 8.5 |
| Shaft Diameter (mm) | (Double D-type) 5.5 |
| No Load Current | 40-180mA. |
| Rated Speed(After Reduction) | 300 RPM |
| Rated Torque | 0.35 Kgcm |
| Weight (gm) | 28 |
| Dimensions in mm (LxWxH) | 65 x 23 x 27 |
| Shipment Weight | 0.135 kg |
| Shipment Dimensions | 8 × 4 × 4 cm |
NEMA 17 34MM Stepper Motor
SPECIFACTION
| Dimensions | 42mm x 42 mm x 34 mm (L x W x W) |
| Movement angle | 1.8 degrees |
| Resistance / phase | 1.5Ω |
| Current / phase | 1.5 A |
| Holding torque | 0.22 Nm |
| Inductance / phase | 2.8 mH |
| Weight | 0.22 kg |
| Diameter of the shaft | 5mm |
Servo SG90
SPECIFACTION
| Model | SG90 |
| Weight(gm) | 9 |
| Operating Voltage | 3.0 – 7.2 V |
| Operating Speed @4.8V | 0.10sec/60° |
| Stall Torque @4.8V | 1.2 kg-cm |
| Stall Torque @6.6V | 1.6 kg-cm |
| Operating Temperature (°C) | -30 to 60 |
| Dead Band Width | 7 μs |
| Gear Type | Glass Fiber |
| Rotational Degree | 180 |
| Servo Plug | JR |
| Cable Length | 25 mm |
| Length (mm) | 22.8 |
| Width (mm) | 12.6 |
| Height (mm) | 34.5 |
| Shipment Weight | 0.125 kg |
| Shipment Dimensions | 8 × 6 × 4 cm |